9mm 135gr Match Winners

[Mike Jeffries]

Looking for some recipes for the 135gr, especially using Bullseye. I do have some Power Pistol and Titegroup, but several pounds of 135gr.

[tkisker]

I’m about to load some 135’s with Titegroup. I’ll let you know what I find out if you’re still wondering. I’m thinking 3.6 Gr. at 1.100 OAL will be good though.

[packnruger44]

Not sure what kind of load you are looking for but I just started using these for idpa.
To make 125 power factor I am using Titegroup
@ 3.4 grains.
Getting 934fps average in a walther pdp 4”
Makes a power factor of 127
Nice soft shooting
low recoil
I’m sure you could push them much harder
If desired

[tkisker]

I was able to chrono a batch of these today. I used Titegroup as well.
Titegroup 3.6 gr.
1.100 OAL
985 fps avg
Power factor approx. 133

Shot out of a Sig P320 X5 Legion. They shot great. Very accurate. I will probably try a few loads lighter now too though.

[Greg Johns]

3.6 gr of TG. 1.10 OAL. 4.6 inch Atlas barrel.
I used a magneto speed chrono, eight inches off the barrel.
Ten shot average 933 /PF 126

Very accurate

[David Trabue]

I’m surprised at the FPS/PF difference in the identical loads immediately above.

.4″ difference in barrel length does not seem like enough to jack up tkisker’s results above that of Greg.

[awalker1-6441]

The difference in the results is similar to my experience.
5 1/2” PCC Taccom (barrel has aluminum tube attached to make 16”)
124 gn RMR RN
4.1 gn HP38
Average fps 1131

Sig X5 Legion 5” barrel
Same load, chronograph and shot before the PCC
Average fps 1061

[Dan]

I just loaded a test batch 135 MW 1.090 OAL. 3.7 Sport Pistol. 938.3 avg. vel. 126.6 pf. Used M&P 5″ Pro for chrono. Ran the gun perfect accuracy great. I did have a hiccup with my Springfield RO. Not the fault of the bullet. recoil spring little on heavy for the light load. Past records show I have been loading that wt. bullet 3.9 gr Sport Pistol, 3.7 Tite Group. 1.09 AOL. will function in All my shooting toys. My “go to” IDPA charge for that weight bullet. (132ish. pf.)

Dan Glica

[Terry Thompson]

I have an old “CRONY”, and here are some results of WW 135’s through my G34 Glock (5.25” BBL). I know the results are somewhat different than others.

1078 fps 5.8 g HS-6
1036 3.6 g Tight Group
957 3.2 g ” ”
956 4.0 g Auto Comp
1065 4.5 g Auto Comp
1163 5.2 g Auto Comp
959 4.0 g CFE Pistol
1053 4.4 g CFE Pistol

P.S. the G34 has a 10 # recoil spring, all locked back the slide last round.
I don’t care what the power factor is.

[sswansonbbg]

Has anyone used the 135’s MW with N320 or N340? Recipe?
Thanks

[Rich Gonzalez]

I’m loading 3.6g of N320 in a scorpion pistol 1.090 & averaging 1,060fps , & also load 3.9g of N340 in a mac5 k & averaging 1,070fps same oal both loads using 135g match winners feed just fine in both w/can .

[BILL WARE]

Hey Guys, Techware here; I haven’t posted in a while but have noticed several threads touting 135s in PDP Steel Frames. So consequently, I am currently in process of loading a batch of RMR 135 MWs over VV N330, and N340 for testing in my 5 inch PDP Steel Frame. Also have a Garmin Xero C1 Chrono, so will also provide data post range days.

[eric wludyka]

waiting for some 135gr mw to get here. loading for atlas apollo and cz ts2 orange. using cfe powder. have garmin also will post some charge weights and col for both guns. i will probably start with Terry Tompson cfe charge. just start a bit lower.

[brunet.christian97]

Did anyone ever find a good recipe for these with CFE Pistol? Also, what is the consensus on a COL for Glock chambers?

[Author]

Posts